• Home
  • Products
  • About
  • Contact

sulfuric acid and steelsulfuric acid corrosion chart

Current Location : Home > sulfuric acid and steelsulfuric acid corrosion chart

  • Corrosion Resistance GuideChampion Fiberglass

    Corrosion Resistance Guide The corrosion guidelines tests were performed by immersing epoxy coupons for 30 days in the chemical at the temperatures shown. This is a very severe test. It has been shown that Champion Duct® can often be used for chemicals listed as "Not Palmitic acid 70 R R Sulfuric acid 81 to 100 N N Paraffin R R

    Get Price
  • HASTELLOY C-276 alloy

    combinations of acid concentration and temperature at which a corrosion rate of 0.5 mm/y (20 mils per year) is expected. Above the line rates over 0.5 mm/y are expected. Between the blue and red lines corrosion rates are expected to fall between 0.1 and 0.5 mm/y. Haynes InternationalHASTELLOY® C-276 alloy

    Get Price
  • Selection Stainless Steel for Handling Sulphuric Acid H2SO4

    Risk of corrosion from self-dilution of sulphuric acid Sulphuric acid has a strong affinity for water extracting water from its surroundings and hence diluting itself. The result can be that acid thought to be safely concentrated for contact with 304 type stainless steels say above 90 can actually attack the steel if water has been

    Get Price
  • Chemical Compatibility Chart

    - Acid nitric HNO3Acid mixed (nitric/sulphuric) HNO3 H2SO4Acid sulphuric 70 to 90 H2SO4 above ambient temperatureAcid oleum H2SO4 (Nordhousen fuming sulphuric) For further definitive information we recommend contacting the chemical supplier or at least testing samples under actual service conditions.

    Get Price
  • What Are the Effects of Sulfuric Acid on Steel (with picture)

    Feb 21 2021 · At certain concentrations sulfuric acid will form a protective layer on steel and the steel will be fine. Other concentrations will yield corrosion and the steel will slowly deteriorate. With corroding steel sulfuric acid often forms hydrogen gas which furthers the corrosion. Low levels of hydrogen gas can cause the steel to groove or warp.

    Get Price
  • CORROSION RESISTANCE OF THE AUSTENITIC CHROMIUM

    Corrosion Resistance of the Austenitic Chromium-Nickel Stainless Steels in Chemical Environments Sulfuric Acid and Ferrous Sulfate Concentration Temperature Length of M F Exposure 245 220 2 yr AlSl Type of st nl s -__- 316 316 Type Expel of iure 99.6

    Get Price
  • Chemical Compatibility Chart

    - Acid nitric HNO3Acid mixed (nitric/sulphuric) HNO3 H2SO4Acid sulphuric 70 to 90 H2SO4 above ambient temperatureAcid oleum H2SO4 (Nordhousen fuming sulphuric) For further definitive information we recommend contacting the chemical supplier or at least testing samples under actual service conditions.

    Get Price
  • Technical DocumentNippon Steel

    to produce sulfuric acid dew-point corrosion. Fig. 1.6 Sulfuric Acid Immersion Test Results under the Atmosphere-solution Equilibrium State of Sulfuric Acid and Hydrogen Fig. 1.7 Corrosion Mass of Steel in H 2SO 4 Chemical composition ( ) 0 20 40 60 80 100 200 400 600 SUS 430 SUS 410 SUS 304 SUS 316 S-TEN 1 S-TEN 2 Corrosion mass (mg/cm

    Get Price
  • Enhanced corrosion resistance of stainless steel type 316

    Jun 01 2018 · In dilute solution sulphuric acid is a strong dibasic acid forming two series of salts. Its diverse use in industry accounts for its selection in this work. The egg shell powder (ES) is expected to give an appreciable amount of electrochemical activities of corrosion inhibition for the stainless steel Type 316 in sulphuric acid environment.

    Get Price
  • Corrosion Behaviour of Mild Steel in Sulphuric Acid

    The corrosion of steel is the most common form of corrosion especially in acid solution. Sulphuric acid is also an important mineral acid with many uses in the same systems and leads the researchers to the study of the effect of the corrosion inhibitors 1–4 .

    Get Price
  • Corrosion Resistance ChartDixon Valve US

    Agent Material Selection 4 Ratings given are based at 70°F (21°C). dixonvalve Aluminum Brass Bronze Hastelloy C-276 Malleable Iron Carbon Steel Monel Stainless Steel 304 Stainless Steel 316 Nylon Polypropylene Seal Material Hydrofluosilicic Acid (10-50 ) X 2 X 2 X 2 X 2 XTEVNB Hydrogen Hydrogen Peroxide (50 )X X 2 X 2- X A TEV

    Get Price
  • Sulfuric Acid Storage GuideAetna Plastics

    • Sulfuric acid is extremely heavy and will test the mechanical integrity of your storage tank. The inherent weight of sulfuric acid requires a strong material that can withstand the static load pressure constantly pressing against the bottom third of the storage tank. • Sulfuric acid is an aggressive oxidizer.

    Get Price
  • CORROSION EROSION OF 316L STAINLESS STEEL IN SULFURIC ACID

    It can be concluded the following SS 316 L that is used in a sulfuric acid plant with a concentratio n of 98.5 H2SO4 and 8488 o C. temperature occurs damage form which follo ws the

    Get Price
  • Enhanced corrosion resistance of stainless steel type 316

    Jun 01 2018 · In dilute solution sulphuric acid is a strong dibasic acid forming two series of salts. Its diverse use in industry accounts for its selection in this work. The egg shell powder (ES) is expected to give an appreciable amount of electrochemical activities of corrosion inhibition for the stainless steel Type 316 in sulphuric acid environment.

    Get Price
  • The performance of stainless steels in concentrated

    velocities than 316L in strong sulphuric acid. Tests in stronger acid showed even lower corrosion rates. Silicon additions tend to remove the velocity sensitivity of stainless steels to corrosion in hot strong sulphuric acid. report extremely low corrosion rates (<0.01mm/y) for SX in 96 acid at 70°C and 25m/sec in the alloy data sheet.

    Get Price
  • Sulphuric Acid corrosion to stainless steel

    Oct 15 2013 · Sulphuric Acid corrosion to stainless steel. Current question and answers October 15 2013. Q. I am considering injecting 93 sulfuric acid at 0.1 gpm into a 2" water line at 25 gpm. The line is 316L stainless and injection quill is CPVC.

    Get Price
  • Hastelloy C-276 Corrosion Resistance to Sulfuric Acid

    The two isocorrosion diagrams shown below illustrate relative corrosion resistance of Hastelloy C-276 material to sulfuric acid or sulfuric acid with 200 ppm chloride ions respectively. The two diagrams are based on corrosion tests conducted on Hastelloy C-276 specimens (ASTM B575 Gr. N10276 plates) which are solution heat treated and in

    Get Price
  • Corrosion resistance of silicon carbideGAB Neumann

    Corrosion resistance. Pressureless sintered silicon carbide is almost universally corrosion-resistant. It resists against all common acids (e.g. hydrochloric acid sulfuric acid hydrobromic acid and hydrofluoric acid) bases (e.g. amines potash and caustic soda) all solvents and oxidizing media (e.g. nitric acid). The graph below shows the

    Get Price
  • Technical DocumentNippon Steel

    to produce sulfuric acid dew-point corrosion. Fig. 1.6 Sulfuric Acid Immersion Test Results under the Atmosphere-solution Equilibrium State of Sulfuric Acid and Hydrogen Fig. 1.7 Corrosion Mass of Steel in H 2SO 4 Chemical composition ( ) 0 20 40 60 80 100 200 400 600 SUS 430 SUS 410 SUS 304 SUS 316 S-TEN 1 S-TEN 2 Corrosion mass (mg/cm

    Get Price
  • Sulphuric Acid corrosion to stainless steel

    Oct 15 2013 · Sulphuric Acid corrosion to stainless steel. Current question and answers October 15 2013. Q. I am considering injecting 93 sulfuric acid at 0.1 gpm into a 2" water line at 25 gpm. The line is 316L stainless and injection quill is CPVC.

    Get Price
  • Polypropylene Chemical Resistance Guide

    by chlorosulfonic acid and oleum at room temperature 98 sulfuric acid 30 hydrochloric acid and 30 hydrogen peroxide at 100°C (212°F). They are also affected by 98 sulfuric acid at 60°C (140°F) and fuming nitric acid and liquid bromine at room temperatures. Under strain

    Get Price
  • IBP1218 09 CORROSION BY CONCENTRATED SULFURIC

    From this Figure it can be noted that for 70 of sulfuric acid the corrosion rate is slightly smaller than 0.5 mm/year at 24 ºC while the rate increases about 10 times (5 mm/year) when the temperature is increased up to 107 ºC. For 98 the corrosion rate is about 0.13 mm/year at 24 ºC and less than

    Get Price
  • High-Performance Alloys for Resistance to Aqueous Corrosion

    Corrosion Problems and Alloy Solutions 1 Corrosion-Resistant Alloys from the Special Metals Group of Companies 4 Alloy Selection for Corrosive Environments 11 Corrosion by Acids 12 Sulfuric Acid 12 Hydrochloric Acid 17 Hydrofluoric Acid 20 Phosphoric Acid 22 Nitric Acid 25 Organic Acids 26 Corrosion by Alkalies 28 Corrosion by Salts 31

    Get Price
  • Chemical Resistance ChartJasper

    Chemical Resistance Chart Introduction Corrosion and degradation depend on many parameters soldering) • Mechanical stress of materials Due to the many parameters influencing the process the corrosion table can only be used as guidance and do not always apply to the actual process Sulphuric acid Nitric acid H2SO4 / HNO3 (1 1) o

    Get Price
  • Corrosion Resistance GuideChampion Fiberglass

    Corrosion Resistance Guide The corrosion guidelines tests were performed by immersing epoxy coupons for 30 days in the chemical at the temperatures shown. This is a very severe test. It has been shown that Champion Duct® can often be used for chemicals listed as "Not Palmitic acid 70 R R Sulfuric acid 81 to 100 N N Paraffin R R

    Get Price
  • HASTELLOY C-276 alloy

    combinations of acid concentration and temperature at which a corrosion rate of 0.5 mm/y (20 mils per year) is expected. Above the line rates over 0.5 mm/y are expected. Between the blue and red lines corrosion rates are expected to fall between 0.1 and 0.5 mm/y. Haynes InternationalHASTELLOY® C-276 alloy

    Get Price
  • Corrosion resistance of duplex stainless steels

    The prevention of corrosion is assumed to be suitable if the attack rate is lower than 0.1 mm per year. Duplex steel grades contain large magnitude of chromium that enables them to offer good corrosion resistance in the different environments. Sulfuric acid. Following diagram shows the corrosion resistance in sulfuric acid.

    Get Price
  • IBP1218 09 CORROSION BY CONCENTRATED SULFURIC

    From this Figure it can be noted that for 70 of sulfuric acid the corrosion rate is slightly smaller than 0.5 mm/year at 24 ºC while the rate increases about 10 times (5 mm/year) when the temperature is increased up to 107 ºC. For 98 the corrosion rate is about 0.13 mm/year at 24 ºC and less than

    Get Price
  • Nitrile Glove Chemical-Compatibility Reference

    Skin corrosion hazard and/or high toxicity Concentrated acetic acid 88 Formic acid 30 Ammonium hydroxide 70 Nitric acid 95 Sulfuric acid Hydrofluoric acid (HF) Nitrile Glove Chemical-Compatibility Reference Disposable nitrile gloves do not provide protection against these highly corrosive chemicals. These are just a few examples.

    Get Price
  • 316L Stainless Steel Chemical Compatibility Chart from ISM

    316L Stainless Steel Chemical Compatibility Chart ver 10-Jan-2020 industrials Key to General Chemical Resistance all data based on 72 ° (22 °C) unless noted Explanation of Footnotes 1Satisfactory to 120° F (48° C) A = ExcellentNo Effect C = FairModerate Effect not recommended

    Get Price

Products News

  • natural gas flame color for boilers horizontal steam boilerboilers
  • total petrochemicals port arthur
  • free opening performance of steel ladle as a function of
  • bostik s best adhesivebostik best spec sheet
  • corundum castable refractory iihigh strength corundum mullite refractory castable
  • increasing the efficiency of pulverised coal fired power
  • industrial hi temp cleaning tools starter kit ecolab
  • how does induction annealing work induction annealing
  • 5 best ceramic glues
  • refractory bricks induction furnace lining insulatingvery high temperature corrosion of chromia and

Product Center

  • Alumina Hollow Ball Bricks
  • Corundum Spinel Castable
  • High Alumina Refractory Cement
  • High Alumina Low Cement Castable
  • High Alumina Refractory Ramming Mass
  • Trough Refractory Castable
  • Magnesium Iron Spinel Brick
  • Mullite Brick
  • Zirconium Mullite Brick

Hot Products

  • Light Weight Silica Insulation Brick
  • Zirconia Hollow Sphere Brick
  • Corundum Refractory Castable
  • Heavy Alkali Resistant Castable
  • High Alumina Low Cement Castable
  • High Alumina Self Flowing Castable
  • Micro Expansion Refractory Plastic
  • Phosphate Refractory Mud
  • Magnesia Zircon Brick

Images Show

About Us

Rongsheng's main products are various types of unshaped refractory products, which are widely used in metallurgy, nonferrous metals, building materials, electric power, petrochemical and other industries.

Rongsheng pays attention to technological innovation and product research and development, and has established close cooperative relations with many universities and scientific research institutes.

Zhengzhou Rongsheng Company © Copyrights. Sitemap